zincopen39 – https://www.repairmywindowsanddoors.co.uk/wembley-windowrepair/

Replacing uPVC Window HandlesThe replacement of window handles made of upvc is a fairly straightforward job. It is essential to ensure that the replacement handle fits inside the spindle cutout in the window mechanism.If you follow the steps below, any cockspur handle will fit most windows. The step height of the handle is key.What to Look ForMany of the windows in the UK are fitted with uPVC handles Over time, they can begin to show signs of wear and wear and tear. When this occurs, the window handle can become loose or difficult to operate, which makes it essential to replace it. This is a relatively easy task that is achievable by anyone who is familiar with basic hand tools.The first step is to ensure that the handle is securely attached to the window frame and in a position that is open. The next step is to locate the pins or screws that hold the handle in place. These are typically located on the inside of the handle and can be removed with a screwdriver or pliers.Once the handle has become loose it can be taken from its hinges by gently pulling off. Then, you’ll need to locate a new handle in the same size and style. This can be accomplished in an online store or in a DIY store. The procedure should take just five minutes and a screwdriver is all you need.One important factor to consider when replacing a uPVC window handle is the step height. This is the distance between the handle’s base and where it is placed in the frame of the window. This is a standard measurement, and you should verify the step height before ordering an replacement handle.There are several sizes depending on the kind of handle. Inline handles are available for uPVC window with lug centres of 31mm, while cockspur handles come with lug centres of 43mm. Tilt-and-turn handles are common on uPVC Windows. They have a specific design that lets the window be tilted for ventilation and then rotated to fully open the window.The most common uPVC handle breakage is internal cracking rather than a breakage from the base. This can make them hard to open and therefore it is crucial to ensure that the replacement handle you purchase has the same spindle length that your current one.Remove the handle that was previously usedIf your window handles are damaged or not properly fitted, they can cause double-glazed windows to close and open incorrectly. They may even get stuck. There are a myriad of reasons, such as general wear and tear, or corrosion of the handle made of metal. In these cases it is crucial to find replacement upvc window handles immediately to prevent further damage and loss of function.One of the first steps to do when replacing upvc window handles is to remove the old handle from the window. To do this, start by removing the screw that is encased when the handle is in a closed position. This should reveal another screw and once removed, you are able to begin to remove the handle itself. You can make the job easier by using an electronic screwdriver.It is also worth noting that the screws on the handle could be hidden behind plastic caps, therefore it is a good idea to take a Stanley knife to the screw caps and then take them off. After the old handle has been removed, examine the square cut on the base of the handle to make sure that the new window lock handles will work with it. This is important as you’ll need to measure the length of the spindle on the old handle to ensure that it is the same size as the window mechanism and the handle spindle that has been cut out.The different kinds of window handles made of upvc are: Espag handles, which are equipped with a central screw and can turn left or right; Cranked handles which have two screws and are typically found on tilt and turn upvc windows as well as Spade handles, which have an arm with a flat surface and can be placed on either side of the window. It is simple to replace the handle once you’ve found one that is suitable. Simply screw it into the frame, and ensure that the spindle is properly inserted into the lock mechanism. After that, you can, tighten the handle to the window frame. Your replacement upvc handles should now be secured.Measure the SpindleIf you need to replace a upvc handle that has fallen, it’s likely the spindle holding it in place is damaged or is loose. In some cases you can tighten the spindle with pin or screw. In certain situations it might be necessary to replace the handle. There are many kinds of window handles made from upvc. They include espagnolette handles that are inline or cockspur handles. They also have tilt and turn handles. Each kind has a distinct method for installing and replacing the handle.Before purchasing a replacement handle it’s important to know the size of the handle that is currently in use. This will ensure that the handle will fit the window in a proper manner and will be of the correct size. Luckily, all handles conform to industry standards of sizing making it relatively easy to identify the right size.To determine the size of your handle first remove it from the window by turning it back to the open position. Then, you should be able to see the size of the screw or pin that secures it. Use a ruler or a tape measure to determine the length the spindle is. Once you have determined the length of the spindle you can purchase a replacement one that is exactly the same size.When you are looking to replace a handle you should consider the step height of the window handle made of upvc. The step height is the distance from the base of the handle to the point at which it sits on the frame. It is typically around 21mm or 9mm in aluminium and uPVC. Dropping something into the space will allow you to observe how far the handle extends before it meets an obstruction.Cockspur handles often have different backset heights depending on the type of window they are placed in. Inline Espag handles have an average height of 43mm centre to centre (2 fixing points). Cockspur handles have different backsets, based on which window design they are placed in. This is because they have an extension spur that extends from the handle and locks over a cockspur wedge striker plate.Install the new handleWhen you’ve picked a new handle, carefully align it with the screw holes on the door and secure it using the screws supplied. Install the latch lever in similar fashion to the handle on the main handle if you are also replacing the door handle. After that, attach the door trim to conceal the mounting screws and finish the job.Tip: To remove a metal head from a wooden wedge place the handle on the floor so that its wide end is on the ground. Then, use an hammer and tap the thin end. Be careful not to scratch the handle or spindle.