answerbugle56 – https://www.repairmywindowsanddoors.co.uk/suttoncoldfield-windowrepair/

Replacing uPVC Window HandlesIt is simple to swap the handles on windows made of upvc. It is crucial to ensure that the new handle fits into the spindle cutouts in the window mechanism.If you follow the steps below any cockspur handle can fit on most windows. The most important factor is the step height of the handle.What to look forMany of the windows in the UK come with uPVC handles and, over time, they will begin to show signs of wear and wear and tear. When this occurs, the handle may become loose or difficult to operate, making it essential to replace it. Anyone who is familiar with basic hand tools is able to complete this job.The first step is to ensure that the handle is securely fixed to the frame of the window in its open position. The next step is to locate the fixing screws or pins that hold the handle in position. These are typically located on the inside of the handle. They can be removed with a screwdriver, or pliers.When the handle has become loose and sagging, gently pull it back from its hinges. It is then necessary to locate a replacement handle that is the same design and size. This can be done in a DIY store or online. The process should take only five minutes, and you will need a screwdriver.When replacing a uPVC handle It is crucial to consider the step height. This is the distance from the base of the handle to the point at which it sits on the frame of the window. It is generally an accepted measurement, however it is essential that you examine the step height of your existing handle before purchasing the new one.There are various sizes depending on the type of handle. Inline handles are available for uPVC windows that have lug centres of 31mm while cockspur handles come with centers of lugs of 43 millimetres. Tilt-and-turn handles are common on uPVC windows. They have a special design which allows the window be tilted for ventilation and then turned to fully open the window.The most common uPVC handle breakage is internal cracking instead of a break at the base. This can make it difficult to open. It is important to ensure that any replacement handle is fitted with the same spindle that was used in your original one.Remove the handle that was previously usedA poorly fitted or damaged window handles can cause your double glazed windows to open and close in a way that isn’t correct and may result in them becoming stuck. There are a myriad of reasons including general wear and tear or corrosion of the metal handle. In these situations, it is vital to replace the upvc window handle as promptly as you can to avoid further damage or loss of functionality.One of the first things to do when replacing window handles made of upvc is to remove the old handle from the window. Start by removing the screw covered with the handle when it is in a closed position. This will reveal a screw and once removed, you are able to begin to remove the handle itself. It is recommended to make use of an electric screwdriver for this as it will make the task easier and quicker.It is also worth noting that the screws on the handle may be hidden behind plastic caps, so it is recommended to take a Stanley knife to the screws and take them off. Once the old handle is removed, you must look at the square cut on the handle’s base to make sure that the new window lock handles will work with it. It is essential to measure the length of the spindle on the handle you used to replace it with and then compare it with the dimensions of the window mechanism spindle cutout.The different types of upvc window handles are: Espag handles, which feature a central screw that will turn left or right; Cranked handles which have two screws and are found on tilt and turn windows made of upvc and Spade handles which have an arm with a flat surface and can be put on either side of the window. When you have a suitable replacement, it’s simply a case of screwing the handle in place and ensuring that the spindle is correctly placed into the lock mechanism. After that, you can, tighten the handle to the window frame. The replacement upvc handle will now be secured.Take a measurement of the SpindleIf you’re replacing a Upvc window handle that has slipped off, it is likely because the spindle that holds it in place is loose or damaged. In some instances it is possible to tighten the spindle by using a screw or pin. In other situations, it will have to be replaced completely. There are several different types of handles made from upvc. There are three kinds of handles: inline espagnolette tilt-and-turn, and cockspur. Each kind has a distinct method of installing and replacing the handle.Before buying a replacement handle it is important to know the dimensions of the handle that is currently in use. This will ensure that the new handle is of the correct size and fits into the window. All handles are measured according to industry standards, so it is easy to find the correct size.To measure the size of your handle, first remove it from the window by turning it back to the open position. You should be able to determine the dimensions of the screw or pin that holds the handle. Make use of a ruler or tape measure to determine the length the spindle is. Once you know the length of the spindle, you can purchase a replacement spindle that is the same length.door handles of a upvc window handle is also important to consider when buying replacements. The step height is the distance from the bottom of the handle until where it rests on the frame. Typically, this will be about 21mm for uPVC windows and 9mm for aluminum. To make sure that the new handle will work it, you can drop something into the space to check how far it goes before meeting an obstruction.Cockspur handles often have different backset heights, based on the style of window they are installed in. Inline the espag handle heights range from 43mm from centre to centre (two fixing points). Cockspur handles however, have different backset heights dependent on the shape of the window they’re in. This is because they have an extension spur that extends from the handle and then locks over a cockspur wedge striker plate.Install the New HandleIf you’ve decided to replace the handle, carefully align it to the screw holes in the door and secure it using the screws supplied. If you’re also replacing the latch lever the lever can be mounted similarly to the door handle. Then, you can reattach the door trim in order to conceal the mounting screws and finish the job.Tips: To take the head of the metal from the wooden wedge make sure the handle is held so that its broad end rests on the floor. Use a hammer to tap on the thin end of the handle. Be careful not to damage the handle or the spindle.