alloyfear4 – https://www.repairmywindowsanddoors.co.uk/patio-door-repairs-london/

www.repairmywindowsanddoors.co.uk – How to Fix a Wet Dog and Save Your Dog From Cold, Wet FeetPatio doors can provide a convenient and comfortable transition between your indoor and outdoor space. They can also save you money on heating and cooling costs by keeping the air inside your home.However, over time your sliding glass or French doors may lose their shine. Fortunately, simple repairs can keep them looking and functioning as new.WeatherstrippingIt’s 5 AM and you’re taking your dog out for his morning constitutional when you stumble into the puddle of water in front of your sliding patio doors. You look around and see that last night’s rain came through the seals of your patio doors. Be prepared, this isn’t going to be a five-minute project. With a bit of patience and a few tools to fix this, you can get it fixed and protect your dog from cold, wet feet.The most important thing is to replace the weatherstripping, which seals the gap between your door and the jamb, keeping out moisture, pests, and drafts. This will also help keep your energy bills low. A quick inspection of your windows or doors will let you know whether the weatherstripping in good condition or needs replacement.There are several types of weatherstripping available that include open-cell and felt foam, thermoplastic rubber, as well as metals such as copper or bronze. Each has advantages and disadvantages. Open cell foam and felt are cheap however they can be ineffective and visible at blocking airflow. Vinyl is more expensive but it holds up well and resists moisture. Rubber is an excellent choice for areas that are heavily used because it won’t wear out as quickly.For installing new weatherstripping, you must first remove the patio doors from the frame using a screwdriver to loosen the screws for adjustment of the roller. Then, using a flathead screwdriver, loosen the plugs that hold weatherstripping at the bottom of frame. Then, remove the weatherstripping that was previously in place and remove any residual adhesive from the bottom of the frame. Then, trim the new to the proper length, peel off the plastic strip at one end, and apply it using a putty blade to the jamb.After that, you can reinstall the door and readjust the roller screws until the door is in the track and is closed properly. Apply waterproof caulk to the place where the stationary panel is positioned to bypass the sliding door and the edge of the stationary panel reaches the frame. This is not a more secure seal than weatherstripping, however it will be able to last for a period of time.Handles and LocksPatio door handles and locks are essential to the security of your home. Over time, they can get damaged or worn out and require replacement. Additionally, the spindle which connects the interior and exterior handles may also need to be replaced.To replace a handle on a patio door, remove the previous one first by taking off any screws that hold it in place. After removing the old handle, you can use a level to ensure that the patio door is straight. If the door isn’t straight it could interfere with the lock. This could lead to problems in the future.Close and open the handle several times after installing it to make sure it’s functioning properly. If you encounter any issues, check the instructions of the manufacturer or a specialist in hardware for assistance. To avoid future issues, it is a good idea also to lubricate your lock mechanism using lubricant made of silicone.The most common type of patio door lock is a mortise lock. It is usually made of steel and fits inside a pocket which has been cut into the door frame. These kinds of locks are typically used on aluminum and wood sliding doors. When replacing a mortise lock, it is important to take a few measurements before purchasing a new lock. You will need to be aware of the location of the mounting holes and the position within the keyway lock.Some patio door handles have an integrated locking mechanism that’s integrated into the handle. These handles have a rectangular key cylinder which fits in the handle’s keyway. If you have this type of patio door, the inside and outside locks are combined into one. This kind of patio door is most often found on aluminum sliding doors.If your patio door latch isn’t able to stay closed the lock tongue might not be properly catching the hasp. Another possibility is that the sliding door isn’t fully parallel to the jamb on the side. The door should be opened by about an inch, then place it against the frame. This will tell you the gap between the jamb and the door. If there is, adjust the rollers on the bottom left or right of the patio door to get it to be perfectly parallel to the jamb.MisalignmentOver time the tracks and rollers will lose their proper alignment. This can cause the doors to become stuck or difficult to move. It also allows cold air and drafts to enter your home, which could decrease energy efficiency. It is possible to correct the misalignment and prevented. Simply applying a silicone-based lubricant to the tracks and rollers will allow your doors to move smoothly once more. It is a good idea to do this periodically to ensure your doors are in top operating condition.A torn screen can also be a problem. It could be a hassle or risky. It could also stop the doors from closing and opening properly, leading to energy loss. In some instances, the screen can be repaired but in others, the door needs to be replaced. If you’re experiencing a torn screen, make sure you clean it thoroughly and try to avoid turning the handles of the door in the wrong way when closing and opening.Over time, hinges can loosen due to normal wear and tear or use. Regularly tightening the screws will help correct this issue and ensure that your doors close securely. This is an easy task which you can perform yourself, but if not sure about it, seek out an expert to ensure that your doors are correctly aligned and secure.It’s recommended to regularly clean your patio doors’ tracks and rollers. Simple vacuuming or brushing can get rid of dust and debris that could hinder the smooth operation of your patio doors. You can utilize a special tool to remove tough dirt or corrosion. It is possible to correct any misalignment by tightening, or examining the screws. But, at times, it is necessary to replace the hinges to ensure a lasting seal.The performance and alignment of your patio doors could be affected when the frames are sagging or sliding. Shifting or warping can occur due to changes in the foundation of your home, but could be caused due to poor installation or through frequent use. A professional can fix or replace the frame of your patio door and ensure it’s aligned properly and functioning at its peak.RollersPatio doors that slide are great to let the outside in while letting ample natural light, but they require some attention to ensure they slide smoothly. If you find that you have to really push the handle to get the door to move, or simply doesn’t move as smoothly as it did in the past then the problem could be the rollers. As time passes, the lower track will fill up with dirt, sand, and mud that makes it hard for the rollers to roll across. You can try cleaning it by spraying it with a lubricant like 2Slick.If the tracks are cleaned and the rollers still aren’t able to move freely It’s time to replace the tracks. Replacement rollers are available for your door and track. They are available at most hardware stores, but you’ll need a partner to assist you in the removal and installation of the rollers. Take a photo of the rollers installed in the frame to help the experts identify the exact type and model you need. You can also search for specific features like bumps or dimples, cutouts or flared edges to narrow down the replacement options.After replacing the rollers, you will need to reinstall the sliding door into its frame. This is a very heavy door, and you might require help. Check to see if there are screws securing the track on either side of the frame. If there are check that they’re loose enough for the bottom of door to drop into the channel that is above the frame. Remove the screen door from the opening. Make sure it’s free of track tracks, rollers and track.Once the new rollers are in place, carefully slide the door into the frame and then swing it down into place. If your new rollers are adjustable they can be adjusted to give the door a clearance in the areas it requires it.